- Welcome to Hesketh Owners Club Forum.
Recent posts
#11
Hesketh-Related Chat / Vampire
Last post by Giovanni Polegato - November 28, 2024, 04:16:34 PMHi Folks, I kindly ask if any of you have an idea of ��how many Vampires have been built or how many are currently registered with the HOC. Thanks for your attention.
Giovanni Polegato
Giovanni Polegato
#12
Requests for Help and (Hopefully) Answers / Clutch master cylinder bleedin...
Last post by Don D - November 24, 2024, 08:44:30 PMHi guys
After starting the Hesketh this morning I found that the clutch would not disengage. I took off the master cylinder, cleaned it out, and installed new seals. The manual indicates that bleeding the system is as simple as opening the bleed valve at the lower end. But I've had no luck getting the air out of the system, that is no pressure is being applied when the LH lever is actuated.
Curiously, this master cylinder has only one bottom hole (I was expecting two). Also, I've tried to verify that the line is clear by applying compressed air at either end while the hose is disconnected - not really a positive test what with the banjo fittings. In any event, lever action does not induce a flow of fluid at the bottom end of the hose.
What am I missing?
After starting the Hesketh this morning I found that the clutch would not disengage. I took off the master cylinder, cleaned it out, and installed new seals. The manual indicates that bleeding the system is as simple as opening the bleed valve at the lower end. But I've had no luck getting the air out of the system, that is no pressure is being applied when the LH lever is actuated.
Curiously, this master cylinder has only one bottom hole (I was expecting two). Also, I've tried to verify that the line is clear by applying compressed air at either end while the hose is disconnected - not really a positive test what with the banjo fittings. In any event, lever action does not induce a flow of fluid at the bottom end of the hose.
What am I missing?
#13
Hesketh Bits and Pieces Wanted / Hesketh Engine
Last post by David B - October 27, 2024, 06:18:13 PMHi a long shot I know but does anyone have or know of a complete engine for sale any condition?
I have an almost complete rolling chassis and an engine would allow another V1000 to hit the road.
I would consider a complete bike for restoration if such a thing exists?
I have an almost complete rolling chassis and an engine would allow another V1000 to hit the road.
I would consider a complete bike for restoration if such a thing exists?
#14
Requests for Help and (Hopefully) Answers / Re: Clutch Plates
Last post by Dave Snr - June 18, 2024, 12:54:48 PMHi Kevin. Yes, I have been told the clutch plates are Ducati under description Surflex S1425. Although there were variations and maybe an extra plate for the Hesketh. However the most common reason for clutch slip is master cylinder not retuning fully or push rod adjustment tight. Check master cylinder action to make sure piston returns fully - compare it to the brake. Operate the clutch, release it and then loosen the bleed nipple to see if it's holding pressure. Both brake and clutch are Brembo 15mm and the seal kits are PS15. I've had to change my seals twice over the years, but never the plates or springs, although it's worth cleaning debris off the plates inner and outer if you get clutch drag. Clutch push rod adjustment is easy to check and make sure there is free play.
Dave
Dave
#15
Requests for Help and (Hopefully) Answers / Clutch Plates
Last post by Kevin B - June 10, 2024, 10:48:03 AMAfter a great weekend away on the Hesketh the clutch started slipping on the way home. The hydraulics seem fine and the bike has done almost 44k miles so I figure it will need a set of plates and springs.
Can anybody tell me where the plates come from. I would assume 1980 ish 900ss Ducati - would that be correct?
Kevin
Can anybody tell me where the plates come from. I would assume 1980 ish 900ss Ducati - would that be correct?
Kevin
#16
Events List 2024 / International Classic Motorcyc...
Last post by velocollins - April 17, 2024, 02:17:13 PMThe Hesketh Owners Club will be at Stafford on Saturday 20th and Sunday 21st April on stand S10 in Side Hall.
Look forward to seeing you all.
Look forward to seeing you all.
#17
Hesketh Bits and Pieces Wanted / Re: ASTRALITES Wanted
Last post by Kevin B - March 10, 2024, 12:55:05 PMRob, I met a guy yesterday who says he has Astrolite wheels that he bought at the factory auction. I don't know if you, or anyone else, still wants wheels but I have his contact details if needed.
Kevin
Kevin
#18
Events List 2024 / HOC AGM Midday Sunday 7th Apri...
Last post by HOCAdmin - February 29, 2024, 09:12:41 PMThis years AGM will be hosted at Clare & Peter Whites facility in Soham. It will start at midday and it will be your opportunity to join other members to discuss the future of the club. Refreshments will be available and there will be the opportunity to purchase Hesketh V1000 spares from Clare's Spares.
#19
Hesketh-Related Chat / HOC Forum and Facebook
Last post by velocollins - January 12, 2024, 06:47:28 PMDear HOC Members,
If you place technical information on HOC Facebook site, please remember to update the Forum with the information as not all member have access to Facebook.
This will ensure their is a central repository for all technical information.
If you place technical information on HOC Facebook site, please remember to update the Forum with the information as not all member have access to Facebook.
This will ensure their is a central repository for all technical information.
#20
Hesketh-Related Chat / Re: HOC Social Event
Last post by velocollins - September 15, 2023, 06:42:28 AMThis was a great weekend meeting up with the Vincent Owners Club at Hampton Loade on the River Seven.